ASTM A252 Steel Pipe Pile

Jan 22, 2024

  • GNEE offers A252 pipe piles:

We offer steel pipe piles in compliance with ASTM A252 standards under the following conditions:
Levels: 1, 2 and 3
Sizes: Seamless and welded up to 48 inches
Type: Seamless, Welded (ER Seamless, Welded (ERW, LSAW, SSAW, DSAW)
Thickness Schedule STD, 40, XS, 80, XXS, 160
Length: 6 meters, 12 meters or customized.
End: chamfer, flat end
Coating treatment: FBE, 3PE, galvanized

  • ASTM A252 Class 3 - Common Pipe Pile Materials

The most common pipe pile material is ASTM A252 Grade 3 steel pipe, which is available as seamless or welded pipe, with welded pipe required in most cases due to the large diameter pipe piles required. A252 Grade 3 steel pipe is stronger, with a tensile strength of 455 MPa (66,000 psi) and a yield strength of 310 MPa (45,000 psi).

  • ASTM A252 Standard Scope

ASTM A252 is the standard specification for welded and seamless steel pipe piles. It is applicable to cylindrical steel pipes with nominal wall thickness, excluding rectangular pipes. These round tubes are used for piling and are used to carry and withstand pressure permanently. In addition, the round tubes serve as tank shells that are filled with concrete piles after the project is completed.

This standard specifies values in inch-pounds (also convertible to SI units) that provide engineers or designers with reference data for A252 piping as a basis for building strength.

  • ASTM A252 Types of Pipe Pile Manufacturing

ASTM A252 pipe piles are manufactured in types including seamless and welded pipe piles.

  • Seamless pipe pile

Seamless pipe piles include hot-rolled, cold-drawn and thermal-expansion seamless pipe manufacturing processes.

  • Welded pipe pile

Welded pipe piles include ERW (resistance welded), LSAW (straight arc submerged arc welded) and DSAW/SAW (spiral arc welded pipe).

  • Chemical composition and mechanical properties

ASTM A252 specifies a maximum phosphorus content of 0.050%. This is because phosphorus makes the steel more fragile and brittle, and higher phosphorus content is detrimental to the welding process.

  • Mechanical behavior

astm-a252-pipe-strength

 

 

 

 

 

 

 

 

 

 

 

 

  • Test Methods

Thermal Analysis: Limit P, the thermal analysis report shall be stated in the MTC to the customer.

  • Product Analysis: Specifically, 2 samples per 200 pieces under 14 inches, 2 samples per 100 pieces from 14 to 36 inches, and 2 samples per 3000 feet above 36 inches.
  • Tensile requirements: According to A252 value. If the yield point is ambiguous, test the yield strength corresponding to a permanent deflection of the gauge of 0.2% of the specimen length, or test the total elongation under loading of 0.5% of the gauge length.
  • Dimensional and Weight Tolerances

Allowable tolerances: +/-1% on outside diameter, +/-12% on wall thickness. Weight should be +15% or -5% of theoretical weight.
Lengths: As specified SRL, DRL or fixed lengths of 20' or 40' and custom lengths.

  • Hydrostatic test

Hydrostatic testing is not specified in the ASTM A252 pipe specification because piling pipes are typically filled with cement and concrete and formed and are not used for liquid conveyance, so hydrostatic testing is not required.

  • How steel pile pipes work

Steel pipe piles work when the soil beneath the building is loose, which can affect the building's stability over time. When steel pipe piles are used, the weight is evenly distributed deeper into the soil, where the soil is compact. This is useful for constructing very large buildings where the soil cannot provide the required support.

On the other hand, if the land area is small and there is not enough space to lay footings or foundations, reinforced buildings are used to increase the stability of the ground.