OCTG Pipe Threads
Mar 18, 2024
- API thread
1. Oil casing fitting threads
Oil casing is a highly demanding, large amount of oil drilling project in the depth of machining products. The use of threads will be connected to a single oil casing up to thousands of metres long can withstand hundreds of atmospheric pressure long column - tubular high-pressure containers. 1924 API formulated the first oil well pipe standard, oil casing pipe fitting threads are 10 teeth per inch and 8 teeth per inch V-type threads, but was later replaced by the API 8 threads round threads and ladder-type threads, and is still in use today. API SPEC 5B standard specifies that the commonly used casing threads are round threads (abbreviated as CSG) and partial trapezoidal threads (abbreviated as BCSG).
(1) API round thread
Casing circular thread has casing short circular thread (CSG/STC) and casing long circular thread (LCSG/LTC).
The round threads of tubing are unthickened tubing thread (TBG/NUE) and externally thickened tubing thread (UPTBG/EUE).
Round thread is no shoulder tapered pipe thread, need to have a coupling connection API round thread pipe fitting
2) API Offset Trapezoidal Thread
This kind of thread is designed to improve the resistance to axial tensile or compressive loads and to provide anti-leakage, abbreviated as BCSG/BTC, without shoulder tapered pipe thread, need to be connected with a hoop, with a trapezoidal tooth type, flat top and flat bottom.

- Drilling tool thread
Drilling tool joint threads are used for the connection of drilling tools and drilling column components such as drill collars, drill pipes, drilling tool stabilisers and adapters. At present, the production and inspection standards are mainly based on API SPEC 7, which is called "rotary shoulder connection", and is the most important mechanical mechanism for connecting drilling column components in the petroleum drilling industry. This type of tapered thread is characterised by axial displacement to compensate for the diameter error of the connecting part, resulting in a high degree of interchangeability, compactness and ease of assembly and disassembly. Its technical characteristics for the British tapered pipe thread, shoulder connection, triangular thread, in the pipe connection is very widely used.
1)Numerical thread (NC)
NC thread is the thread recommended by API for priority use, all specifications use V-0.038R flat top and round bottom triangular tooth type, which is characterised by a round bottom radius of 0.038" (0.965mm), taper 1:8, 1:6 and 1:4, used in square drill pipe, drill pipe, drill collar, drill stabiliser, etc. on drilling tools.
2) Regular type thread (REG)
This type of thread is used for connecting the inner thickened drill pipe, the inner diameter of the joint is smaller than the inner diameter of the thickened end, and the inner diameter of the thickened end of the pipe is smaller than the inner diameter of the thickened end.
The main purpose of API's design of regular type threads is to apply them to drill bit connections, where the presence or absence of stress concentrations at the bottom of the threads is irrelevant because the drill bit is located at the end of the column, and API has retained all of their specifications.
All of their specifications have been retained. This type uses V-0.050 and V-0.040 threads, and in API SPEC 7, 40th Edition, a new version was added that uses V-0.050 and V-0.040 threads.
In API SPEC 7, the fortieth edition of the new use of V-0.055 (flat bottom, the top of the tooth width of 0.055 inches, 1397mm) tooth type 1REG and 1-1/2REG
Two sizes of threads.

3) Internal Flat Thread (IF)
This type of drilling tool joint threads to connect the outer thickening or inner and outer thickening of the drill pipe, the formation of drill pipe joint ID, pipe thickening ID and pipe
The inside diameter of the joint, the thickened inside diameter of the pipe body and the inside diameter of the pipe body are equal or similar to the through diameter of the pipe body. All sizes are threaded with V-0.065 flat-topped, flat-bottomed, triangular-shaped threads, which are flat-bottomed and have a 0.065-inch (1.65lmm) wider top. In addition to 5 1/2 IF, and NC thread interchangeability. However, due to the type of thread structure is prone to cause stress concentration, API has been replaced by the NC series.
(4) Through-hole type thread (FH)
Although there are few specifications for this type of thread, it was once widely used in taps, square drill pipes, drill rods, drill collars and drill bits. Now in addition to 5-1/2 FH and 6-5/8FH two kinds of use V-0.050 tooth type, 1:6 taper of the large size thread, the rest of the API out of the thread. The only V-0.065 tooth type 4FH and the same as the internal flat type thread was replaced by the digital thread NC40.
- Special Buckle Threads
Special buckles are pipe threads with special structure different from API threads. Under the special environment of some oilfields, the shortcomings of API threads are obviously shown: although the sealing performance of API round threaded pipe columns is better, the tensile force borne by the threaded part is only equivalent to 60% to 80% of the strength of the pipe body, and thus it cannot be used in the exploitation of deep wells; the tensile performance of the pipe columns connected with API offset trapezoidal threads is much higher than that of the API round threaded connection, but its sealing performance is not very good, and thus it cannot be used for the exploitation of high-pressure gas wells; in addition, the thread grease can only be played in the temperature below 95℃, which is not the best environment. Although the tensile performance of API trapezoidal thread connection is much higher than that of API round thread connection, but its sealing performance is not very good, so it can not be used in the exploitation of high pressure gas wells; in addition, thread grease can only play its role in the environment with the temperature below 95℃, so it can not be used in the exploitation of high-temperature wells.
Compared with API threaded connection, special buckle connection has the following features:
1) Good sealing:ball to taper; ball to cylinder; taper to taper; cylinder to cylinder; shoulder to shoulder.
2) High connection strength and good anti-slip performance:Most of the parameters are adjusted on the basis of partial ladder.
3) Thread surface treatment:Through the selection of materials and the improvement of surface treatment process, the problem of thread sticking buckle is basically solved;
4) Optimisation of shoulder structure: through the reasonable design of shoulder structure, the buckling operation is easier to carry out.




