High-Pressure Seamless 12Cr1MoVG Tube: Heat Treatment and Service
Mar 04, 2024
Product Positioning
High-pressure seamless 12Cr1MoVG tube is the pressure-retaining product form of this Cr-Mo-V grade, made by hot working a solid round rather than by welding a formed plate. The absence of a longitudinal weld seam removes the weld heat-affected zone from the pressure boundary, which is the main reason seamless tube is selected for superheater, reheater, header and main steam piping where the wall is thin relative to the diameter and the operating pressure is high.
The grade combines three strengthening routes: chromium and molybdenum in solid solution, vanadium carbides for precipitation strengthening, and a normalising plus tempering treatment that produces a stable, fine-grained microstructure. Together these allow the tube to operate continuously at elevated temperature without the rapid loss of strength that plain carbon steel suffers above about 400 degrees Celsius.
Steelmaking and Rolling Route
Production begins with melting in an electric arc furnace or a top-blown oxygen converter, followed by secondary refining to bring carbon, phosphorus and sulphur within the narrow window required by the grade. Composition and tapping temperature are controlled closely because vanadium recovery and carbide formation are sensitive to both.
Melting and refining: composition trimmed to the GB 5310 window, with low sulphur needed for impact toughness.
Hot working: the cast round is pierced and rolled to tube on a plug mill, mandrel mill or similar route, with intermediate annealing to relieve internal stress accumulated during reduction.
Heat treatment: normalising and tempering, or quenching and tempering for heavy walls, to develop the specified strength and toughness combination.
Finishing: straightening, cutting to length, end preparation and surface treatment such as pickling, passivation or a protective coating depending on the service environment.
Inspection: dimensional check, visual and non-destructive examination, and mechanical and metallographic testing on the finished tube.
Heat Treatment Regime
| Wall thickness | Route | Austenitising | Tempering |
|---|---|---|---|
| Up to 30 mm | Normalising and tempering | 980 - 1020 C | 720 - 760 C |
| Above 30 mm | Quenching and tempering | 950 - 990 C | 720 - 760 C |
| Above 30 mm, alternative | Normalising and tempering with accelerated cooling | 980 - 1020 C | 720 - 760 C |
Two rules govern the practice. Cooling after austenitising must be fast enough to avoid a coarse or banded structure, particularly in heavy walls, and tempering must be long enough to temper the vanadium carbides without dropping into the range that reduces impact toughness. A repair weld on a finished tube is followed by a local stress relief at a temperature consistent with the original tempering treatment.
Mechanical Properties and Hardness
| Property | Tensile strength | Yield strength min | Elongation min | Impact energy min |
|---|---|---|---|---|
| Longitudinal | 470 - 640 MPa | 255 MPa | 21 % | 40 J |
| Transverse | 470 - 640 MPa | 255 MPa | 19 % | 27 J |
| Hardness | 135 - 195 HBW, approximately 140 - 205 HV | |||
Hardness is the fastest shop-floor indicator that the heat treatment has been carried out as intended. Readings at the top of the band point to insufficient tempering or too fast a cooling rate, while readings below the band usually indicate over-tempering and a corresponding loss of elevated-temperature strength.
Where the Tube Is Used
Petrochemical plant: process piping, reformer and cracking furnace coils, and heat exchanger tube handling hot corrosive media.
Power generation: superheater and reheater tube, economiser tube, headers and main steam lines in fossil-fired boilers.
Marine and offshore: high-pressure shipboard piping and desalination plant tube exposed to salt spray and vibration.
Heavy industry: high-temperature steam and gas transfer lines in metallurgical and chemical works.
Selection for these duties follows from three properties acting together: strength retention at temperature, resistance to steam oxidation through the chromium content, and enough toughness to tolerate thermal cycling without cracking at the restraint points of a header or a support.
Inspection and Quality Control
Finished tube is released against chemical analysis, tensile and impact testing, a body pressure or ultrasonic test, dimensional verification and a metallographic examination of the microstructure. Surface quality is checked for laps, seams and rolled-in scale, since a longitudinal defect on a seamless tube can act as a stress raiser under internal pressure. Where the order specifies it, independent third-party witness testing is arranged before the heat is released for shipment.
FAQ
Q: Why use seamless tube instead of welded tube for boiler service?
Seamless tube has no longitudinal weld, so the pressure boundary contains no weld heat-affected zone and no weld defects to interrogate in the most highly stressed region.
Q: What heat treatment is used for wall thickness above 30 mm?
Quenching from about 950 to 990 degrees Celsius followed by tempering at 720 to 760 degrees Celsius, or normalising and tempering with accelerated cooling after normalising.
Q: How is the delivered heat treatment verified?
By hardness survey, tensile and impact tests on finished tube, and metallographic examination of the microstructure, all reported on the mill test certificate.
Q: Which defects matter most on a seamless pressure tube?
Longitudinal laps and seams are the most significant, because they align with the hoop stress direction and can initiate cracking under internal pressure.
Q: Can the tube be supplied with a corrosion protection coating?
Yes. Pickled, oiled, black painted or coated finishes are available depending on the storage period and the environment at the fabrication yard.
Q: Is a repair weld permitted on the tube body?
Welding on the tube body is normally restricted, and where repair is agreed it is followed by local stress relief consistent with the original tempering treatment and by re-testing.







