3PE Anti-Corrosion Steel Pipe Process: From Shot Blasting to Coating
Feb 21, 2024
How a 3PE Anti-Corrosion Coating Line Works
Three-layer polyethylene (3PE) is the standard external corrosion protection for buried oil, gas and water transmission pipelines: a fusion-bonded epoxy (FBE) primer, a copolymer adhesive layer and a polyethylene topcoat. Because each layer depends on the one beneath it, the line is run as one continuous, monitored process rather than as separate operations. Coating design and acceptance are normally written against GB/T 23257 for buried steel pipelines or ISO 21809-1 for polyolefin (3-layer PE and 3-layer PP) external coatings. The steps below follow the pipe from inspection through blasting, dust removal, preheating, coating, cooling and end cut-back.
Step 1 and 2: Pipe Inspection and Shot Blasting to Sa 2½
Every pipe is inspected individually before processing. Pipes with serious mechanical damage, laps, cracks or dents are marked and rejected. Helically welded pipe with a flattened or out-of-round end is re-rounded where repair is possible, and scrapped if the end cannot be brought back to tolerance.
The pipe is preheated on its outer surface with a flame heater to 40–60 °C before blasting, which drives off moisture, oil and loose contamination and improves descaling quality.
Both ends are plugged with rubber or sponge plugs (or the pipe's own caps where fitted) so that steel shot cannot enter the bore; this also limits shot consumption.
After shot blasting the surface must reach Sa 2½ per GB/T 8923, equivalent to ISO 8501-1, with anchor-pattern depth set to the epoxy powder supplier's recommendation.
Rust, oil and mill scale must be completely removed. Surface defects that could later become coating holidays are ground out, and wall thickness after grinding must stay above the specified minimum. Pipes failing the descaling check are taken off line, cleared of shot and re-blasted.
Step 3 and 4: Fine Dust Removal and Induction Preheating
A fine dust treatment unit removes residual dust immediately before electrostatic spraying. Epoxy powder must be applied within 4 hours of blasting; if that window is exceeded, or if rust bloom appears, surface preparation is repeated. On start-up the extraction fan runs before the dust removal motor, and on interruption the motor stops before the fan. The cyclone collector is cleaned on a fixed interval, the fan is checked after every start, the electrode is maintained on schedule, and the pipe surface is checked at least once per hour. Pipes are then preheated in a constant-power medium-frequency induction unit to the setpoint recommended by the powder manufacturer.
| Parameter | Setting or limit |
|---|---|
| Preheat before descaling | 40–60 °C |
| Preheat before powder coating | Per powder manufacturer, maximum 275 °C |
| Medium-frequency circulating water | Minimum about 3 m³, pipelines checked for leakage before start-up |
| Heating power | Set with a trial pipe for each diameter and line speed |
| Temperature measurement | Calibrated instrument, recorded at least once per hour |
Step 5 and 6: Coating Application, Cooling and End Cut-Back
Epoxy powder is applied by electrostatic spray or roll coating. The adhesive is applied while the epoxy is still in its gelation stage so that the layers bond chemically, and polyethylene follows by side extrusion or tape winding.
With tape winding, the overlap and the polyethylene on both sides of the weld seam must be fully rolled and compacted, and the finished surface must not be crushed by the handling equipment.
Coating is fixed by water cooling immediately after application, using a quench room operated section by section. Cooling water valves are adjusted so the flow does not strike the fresh coating hard enough to mark it.
The pipe passes the first cooling section before the first set of drive wheels, so the coating is already set when it is rolled on rubber wheels. Depending on diameter and ambient temperature, 2–4 cooling sections are used, pipe surface temperature stays below 60 °C, and the fusion-bonded epoxy must be fully cured.
The coating must be flat and even in colour, free from bubbles, cracks and shrinkage holes; a light orange peel pattern is acceptable and thickness must meet the design requirement.
Ends are cut back so that 100–120 mm of bare steel remains for field welding, and the cut-back is dressed with an electric wire brush in 2–3 passes with a flat brush face. The polyethylene end face is chamfered to not more than 30°, up to 20 mm of epoxy coating may remain beyond it, and peeling or warping at the pipe end must be prevented.
Quality Control Checks Along the Line
| Check | Frequency | Acceptance |
|---|---|---|
| Preheat before descaling | Each pipe | 40–60 °C |
| Cleanliness after blasting | Each pipe | Sa 2½ per GB/T 8923 |
| Blasting to powder interval | Continuous record | Maximum 4 hours, no rust bloom |
| Preheat before coating | At least hourly | Per powder specification, maximum 275 °C |
| Coating thickness | 1st, 5th and 10th pipe per batch, then every 10th | Per coating design |
| Coating appearance | Each pipe | Flat, even, no bubbles, cracks or pin holes |
| Cooling temperature | Continuous | Surface below 60 °C, FBE fully cured |
FAQ
Q: Why is the pipe preheated before shot blasting?
A dry, slightly warm surface at 40–60 °C releases moisture and oil more easily and gives a cleaner, more uniform anchor pattern than a cold or damp surface.
Q: What surface grade is required before 3PE coating?
Sa 2½ according to GB/T 8923, equivalent to ISO 8501-1, with anchor-pattern depth set by the epoxy powder supplier. A lower grade leaves rust and scale that become disbonding points later.
Q: How long can a blasted pipe wait before coating?
Epoxy powder must be applied within 4 hours of blasting. If the window is exceeded, or if rust bloom is visible, the surface preparation is repeated before coating.
Q: Why is coating preheat limited to 275 °C?
Above that temperature the powder cures too quickly and can degrade, giving a brittle primer with poor adhesion to the adhesive layer. The practical setpoint follows the powder data for the line speed in use.
Q: Why are the pipe ends left bare?
A cut-back of 100–120 mm leaves bare steel for the field girth weld and its joint coating, with the polyethylene end chamfered to not more than 30° for a smooth tape wrap.
Q: How often is coating thickness checked?
At least the 1st, 5th and 10th pipe of each consecutive batch, and afterwards at least one pipe in every ten, in addition to the continuous visual check of every pipe.







