45 Seamless Steel Pipe: Grade 45 Carbon Steel Tube Properties and Uses
Aug 17, 2023
What Is 45 Seamless Steel Pipe?
Grade 45 is a medium-carbon quality carbon structural steel defined in GB/T 699, and the number refers to the nominal carbon content of about 0.45 %. Seamless tube of this grade is produced by piercing and hot rolling, with cold drawing or cold rolling used where tighter dimensional control and a better surface finish are needed. The combination of roughly 0.45 % carbon with a low-alloy-free composition gives a steel that can be machined, normalised and, when required, quench-and-tempered to a wide spread of strength levels, which is why grade 45 tube serves both machined components and ordinary fluid and structural duty.
Chemical Composition and Mechanical Properties
| Element | Requirement (%) |
|---|---|
| Carbon (C) | 0.42–0.50 |
| Silicon (Si) | 0.17–0.37 |
| Manganese (Mn) | 0.50–0.80 |
| Phosphorus (P), max | 0.035 |
| Sulfur (S), max | 0.035 |
| Chromium (Cr), max | 0.25 |
| Nickel (Ni), max | 0.30 |
| Copper (Cu), max | 0.25 |
| Property | Typical requirement, normalised |
|---|---|
| Tensile strength Rm | 600 MPa minimum |
| Yield strength ReL | 355 MPa minimum |
| Elongation A | 16 % minimum |
| Reduction of area Z | 40 % minimum |
| Hardness as supplied | 229 HBW maximum |
The residual limits on chromium, nickel and copper keep the steel in the plain carbon family and avoid hardenability scatter that would complicate machining. The property values above apply to the normalised delivery condition; quenching and tempering can be specified to raise strength further, but the heat treatment must be agreed between buyer and supplier and the results are then reported per heat treatment batch.
Standards, Size Range and the Advantages of the Seamless Form
GB/T 8162 – seamless steel tubes for structural applications, with dimensional and surface requirements but no pressure service obligation.
GB/T 8163 – seamless steel tubes for liquid service, adding pressure-tightness testing typical for conveying duty.
GB/T 3087 – seamless tubes for low and medium pressure boilers, with controlled microstructure and test frequency.
Sizes are quoted against the selected standard. A commonly supplied example is 273 mm outside diameter × 12 mm wall thickness; delivery is normally hot rolled or normalised, with annealed tube available where extensive machining is planned.
Uniform structure: the cross section is continuous with no weld seam, so strength is consistent along the length with no weld-related weak point.
Pressure and temperature capability: a homogeneous wall normally gives higher pressure and temperature ratings than a welded tube of the same size and wall.
Smooth bore: no internal weld bead means less friction and turbulence, improving flow efficiency and reducing deposit build-up.
Machinability and finish: normalised grade 45 cuts cleanly and takes a good finish, so tube can be used directly as a shaft, sleeve or cylinder body, and cold-drawn tube presents a smoother surface than equivalent welded product.
Limitations, Welding and Corrosion Protection
Length limits: the piercing and rolling route restricts the maximum single length compared with welded pipe, which can increase the number of joints in long runs.
Cost: the seamless process is more complex and generally more expensive than welded pipe for the same nominal size.
Weldability: at about 0.45 % carbon the steel is not as weldable as low-carbon grades. Welding needs a qualified procedure, preheat of roughly 150–200 °C for thicker walls and consideration of post-weld stress relief.
Corrosion: grade 45 is a plain carbon steel and corrodes like any other. Tube is supplied with anti-corrosion oil, varnish or another agreed treatment, and buried or continuously wet service normally calls for an external coating system such as three-layer polyethylene.
Typical applications: machined parts such as shafts, gears, couplings, bushes and piston rods; hydraulic and pneumatic cylinder bodies; fluid conveying lines under GB/T 8163; and steel structures needing a stronger, harder grade than plain low-carbon tube.
FAQ
Q: Is 45 seamless pipe the same as Q355B pipe?
No. Grade 45 is a medium-carbon quality carbon steel to GB/T 699, where the number shows nominal carbon content. Q355B is a low-alloy structural steel to GB/T 1591, where the number shows minimum yield strength. They belong to different steel families and are not interchangeable without checking the design.
Q: What is the difference between GB/T 8162 and GB/T 8163 tube?
GB/T 8162 covers structural duty and concentrates on dimensions and surface quality, while GB/T 8163 covers tube conveying liquid and adds pressure-tightness testing. Tube for a fluid line should be ordered to GB/T 8163 even when the grade is the same.
Q: Can grade 45 tube be welded?
It can, but with more care than low-carbon steel: a qualified procedure, preheat of about 150–200 °C for heavier walls, controlled heat input and post-weld stress relief where required.
Q: What size and delivery condition is normally supplied?
Hot rolled or normalised seamless tube from small bore to heavy wall, for example 273 mm OD × 12 mm WT in mill lengths. Tolerances and delivery condition are stated against the standard chosen.
Q: Why is hardness limited in the delivered condition?
A maximum of 229 HBW in the as-supplied state keeps the tube machinable and avoids the brittle, crack-sensitive structure that excessively fast cooling can produce in a medium-carbon steel.
Q: How is 45 seamless pipe protected in service?
Short-term protection is anti-corrosion oil or varnish. For buried or wet service an external coating system is applied, with pipe ends left bare for field welding and joint coating.







