Analysis of applicable temperature range of different valve materials

Aug 14, 2025

Metallic Valves

‌1. Cast Iron Series‌

‌Gray Cast Iron‌:
Operating temperature: ‌-15°C to 250°C‌.
Suitable for low-pressure water/steam systems; brittleness intensifies with rising temperatures.

‌Malleable Cast Iron‌:
Enhanced toughness via annealing; temperature range: ‌-15°C to 300°C‌.
Common in building water supply/drainage pipelines.

‌Ductile Iron‌:
Optimized graphite morphology; tensile strength ≥400 MPa.
Temperature range: ‌-30°C to 350°C‌ (excels in high-temperature steam pipelines).

‌2. Carbon & Alloy Steels‌

‌Carbon Steel‌:
WCB-grade carbon steel remains stable at ‌-29°C to 425°C‌.
Above 425°C, switch to alloy steels (e.g., WC6 (1.25Cr-0.5Mo) or WC9 (2.25Cr)) with max. temperature ‌593°C‌.

‌Cr-Mo Steel‌:
1Cr5Mo alloy maintains strength at ‌550°C‌;
12Cr1MoVA (vanadium-enhanced) max. temperature ‌570°C‌ (widely used in refinery catalytic cracking units).

‌3. Stainless Steel Series‌

‌Austenitic SS‌:
304 (CF8) and 316 (CF8M): ‌-196°C to 600°C‌ with superior corrosion resistance.
316L (low-carbon) significantly enhances intergranular corrosion resistance in weld zones.

‌Duplex SS‌:
SAF2205: Excellent stress corrosion cracking resistance below ‌300°C‌, ideal for chloride-containing media.

‌4. Special Metals‌

‌Monel Alloy‌:
Ni-Cu-based alloy resists hydrofluoric acid corrosion below ‌400°C‌, used in nuclear plant primary coolant systems.

‌Hastelloy‌:
C-276 maintains corrosion resistance against reducing media up to ‌1100°C‌ (critical for sulfuric acid production).

‌Titanium Alloy‌:
TA2 forms dense oxide films in seawater below ‌300°C‌ (PREN ≥40), widely applied in offshore platforms.

SS Check Valve

Non-Metallic Valves

‌1. Plastic Valves‌

‌Engineering Plastics‌:
PTFE-lined valves: ‌-180°C to 150°C‌ (note cold flow phenomenon);
PVDF: Max. temperature ‌140°C‌ due to enhanced crystallinity.

‌Thermoplastics‌:
PEEK retains mechanical properties at ‌260°C‌ (high-cost; used in semiconductor manufacturing).

‌2. Rubber Valves‌

‌General Rubber‌:
NBR: Resists mineral oils below ‌80°C‌;
CR: Max. temperature ‌100°C‌ (chlorine-enhanced structure).

‌Specialty Rubber‌:
FKM maintains sealing at ‌200°C‌ (standard in aviation hydraulic systems).

 

Special-Material Valves

‌1. Ceramic Valves‌

‌Alumina Ceramic‌:
Hardness HRA≥88 below ‌1000°C‌ (volume density ≥3.8 g/cm³);
Temperature ramp rate must be ≤‌10°C/min‌ to avoid microcracks.

‌Silicon Carbide Ceramic‌:
Reaction-bonded SiC: Thermal conductivity 83 W/(m·K) at ‌1380°C‌ (ideal for waste incinerator flue gas).

‌2. Glass & Enamel Valves‌

‌Borosilicate Glass‌:
Linear expansion coefficient 3.3×10⁻⁶/°C; visual fluid monitoring below ‌90°C‌ (avoid mechanical impact).

‌Enamel Valves‌:
Steel-based enamel resists acid below ‌150°C‌; beyond this, use zirconium-containing base glaze for thermal stability.

bronze check valve

Engineering Application Guidelines

‌Temperature-Pressure Coupling‌:
Carbon steel's allowable stress drops ‌40%‌ at 425°C; pressure-temperature rating must be verified per ‌ASME B16.34‌.

‌Thermal Cycling‌:
For ceramic valves cycled frequently between ‌100–300°C‌, limit temperature ramp rate to ‌30°C/h‌ to prevent thermal shock cracks.

‌Phase Change Impact‌:
Liquid ethylene expands ‌240-fold‌ when vaporized at ‌-104°C‌; cryogenic valves require bidirectional sealing and pressure-relief devices.

‌Material selection must balance thermodynamics, chemical stability, and cost-effectiveness.‌
‌Recommendations‌:

Conduct thermo-structural coupling analysis via ‌ANSYS Workbench‌;

Validate corrosion resistance using ‌ASTM G28‌;

Optimize lifecycle costs holistically.