Anti-Corrosion Coating Surface Treatment for Steel Pipe

Oct 16, 2023

Why Surface Treatment Decides Coating Performance

A coating protects steel by isolating it from the corrosive medium, and that isolation only works if the coating stays bonded. Bonding is created by the surface itself: cleanliness, roughness and the absence of soluble salts determine how well the first coat wets and anchors to the steel. Practical experience consistently shows that most premature coating failures, blistering, peeling and undercutting from a scribe, begin at the steel to coating interface rather than in the coating chemistry.

Good practice therefore separates the work into three stages: remove all contaminants and loose material, generate a suitable anchor profile, and apply the primer before the prepared surface starts to deteriorate. Each stage has its own inspection criteria, described below.

Blast Cleaning Requirements to Sa 2.5

Coating anti-corrosion means applying a uniform layer of paint or a composite lining to a prepared steel surface so that the steel is isolated from the corrosive medium. Abrasive blast cleaning is the standard preparation method for pipe and tube. The usual acceptance grade is Sa 2.5 of ISO 8501-1, described as very thorough blast cleaning, in which all grease, mill scale, rust and previous coating are removed and any remaining residue is limited to light shadows, stripes or spots that do not exceed about five percent of the unit area.

Compressed air must be free of oil and water, so a filter and moisture trap at the nozzle are normal equipment.

The abrasive must be dry, clean and free of dust, salt and other contaminants.

Visible grease and dirt must be removed by solvent or alkaline cleaning before blasting, because blasting alone can drive contamination into the steel surface.

Weld spatter, burrs, sharp edges, undercut and weld slag must be ground or chipped away and edges rounded before blasting begins.

Blasting must not be carried out when the steel temperature is less than 3 °C above the dew point, because condensation will form on the freshly cleaned surface.

Relative humidity, steel temperature and dew point are recorded during the work so that the result can be verified afterwards.

Anchor Profile and Primer Compatibility

After rust removal, the surface roughness of the base layer is designed to reach 40-65 µm, which is compatible with the thickness of the anti-corrosion primer and provides the mechanical key the coating needs. The profile is controlled by abrasive type and size, air pressure, and the angle and distance of the nozzle, and it is verified against the surface roughness comparators of ISO 8503-1 before the first coat is applied. Too low a profile gives poor adhesion, while too high a profile can leave peaks that the primer cannot fully cover, which leads to early rust spotting.

The primer must be compatible with both the profile and the following coats. A zinc rich or epoxy primer is normally applied by airless spray to the dry film thickness stated in the coating data sheet, with thickness verified on the blasted surface in accordance with the applicable dry film thickness measurement method. Intermediate and top coats follow within the overcoating window defined by the coating manufacturer, since exceeding that window means the surface has to be re-prepared or treated to restore intercoat adhesion.

Hand and Power Tool Cleaning Where Blasting Is Not Possible

Where rust has already appeared on a partly coated surface, or where geometry prevents blasting, local preparation is carried out by hand or power tools. The acceptance grade for this work is St 3 of ISO 8501-1, very thorough hand and power tool cleaning, which requires the surface to be free of visible oil, grease and loose matter, with only light, tightly adherent staining remaining in the form of dots or narrow strips. Discs, wire brushes and needle guns are used, followed by vacuuming and solvent wiping to remove dust and oil.

Tool cleaning produces a much lower roughness than blasting, so a coating selected for these areas must be one that tolerates a smoother substrate, and the dry film thickness may have to be increased to compensate for the reduced profile. Repair areas are feathered into the intact coating so that no step is left at the boundary, and the repaired area is inspected for continuity before the next coat.

Coating Systems and Site Sequencing

System Typical standard Service
Fusion bonded epoxy ISO 21809-2 Buried and immersed pipelines with high adhesion demand
Three layer polyethylene ISO 21809-1 Buried long distance pipelines needing damage resistance
Three layer polypropylene ISO 21809-1 Higher temperature pipelines and offshore service
Liquid epoxy and polyurethane Coating data sheet Exposed steelwork, splash zone and repair work
Cement mortar lining ISO 4179 Internal lining of water and drainage pipe

Sequencing matters as much as material choice. The sandblasting area must be kept away from the painting area so that dust and abrasive cannot settle on a wet film; where site conditions prevent separation, blasting is finished completely and the dust is allowed to settle before painting starts. Preparation and inspection are followed immediately by priming, usually within a few hours, so that the surface does not flash rust. Field joints welded after factory coating are prepared locally to the same criteria and then protected with a compatible repair system such as a heat shrink sleeve or a liquid epoxy. Once cured, the coating is checked for continuity with a holiday detector, for film thickness and for adhesion, and every defect is repaired before backfilling or hydrostatic testing.

Frequently Asked Questions

Q: What exactly does Sa 2.5 mean?
It is the very thorough blast cleaning grade of ISO 8501-1. All grease, scale, rust and old coating are removed, and only slight shadows, stripes or spots of contamination may remain, not exceeding about five percent of the unit area.

Q: What anchor profile should be measured after blasting?
A roughness of 40-65 µm is the usual requirement for pipe coatings, verified with the ISO 8503-1 comparators. It has to suit the primer thickness so that the peaks are fully covered.

Q: Can hand tool cleaning replace blasting?
Only for local repairs and inaccessible areas. Hand and power tool cleaning to St 3 removes loose matter but produces a much lower profile, so the coating system and thickness must be adjusted accordingly.

Q: How soon must the primer be applied after blasting?
As soon as possible, in practice within a few hours, and only while the surface remains clean, dry and free of flash rust. Any surface that has visibly deteriorated must be re-blasted.

Q: Which coating system suits a buried pipeline?
Fusion bonded epoxy to ISO 21809-2 or three layer polyethylene to ISO 21809-1 are the common choices. Both rely on correct surface preparation, and the field joints need a compatible repair coating.

Q: Why must the blasting and painting areas be separated?
Because dust and spent abrasive settling on a wet film contaminate it and create holidays in the coating. Where separation is impossible, blasting is completed and the dust allowed to settle before painting starts.