api 5l x42 vs x52 pipeline for oil and gas

Mar 28, 2026

API 5L X42 and API 5L X52 are two commonly used steel grades in oil and gas pipelines. The core difference lies in their strength grade, applicable operating conditions, and technical requirements. X52 has higher mechanical properties, with a minimum yield strength of 359 MPa, while X42 has 290 MPa. This means that X52 can withstand greater internal pressure and external loads, making it more suitable for trunk line projects under high pressure, long distances, or complex geological conditions, such as major projects like the West-East Gas Pipeline.

High-pressure transmission: X52; low-pressure projects: X42? Our engineers will help you figure it out!

 

Mechanical Properties Comparison

Parameter Unit API 5L X42 (L290) API 5L X52 (L360)
Yield Strength (min) MPa (ksi)

≥≥

290 (42.1)

≥≥

360 (52.2)
Tensile Strength (min) MPa (ksi)

≥≥

415 (60.2)

≥≥

460 (66.7)
Yield to Tensile Ratio - Max 0.93 (PSL2 only) Max 0.93 (PSL2 only)
Elongation % Calculated based on area Calculated based on area

 

Chemical Composition Comparison

PSL1 (Basic Requirements)

Element (Max %) X42 (PSL1) X52 (PSL1)
Carbon (C) 0.28% 0.28%
Manganese (Mn) 1.30% 1.40%
Phosphorus (P) 0.030% 0.030%
Sulfur (S) 0.030% 0.030%
Micro-alloys (Nb/V/Ti) Optional Usually added

PSL2 (Strict Requirements)

Element (Max %) X42 (PSL2) X52 (PSL2)
Carbon (C) 0.24% 0.24%
Manganese (Mn) 1.15% (Smls) / 1.30% (Wld) 1.40%
Phosphorus (P) 0.025% 0.025%
Sulfur (S) 0.015% 0.015%
CEV (Carbon Equiv.)

≤≤

0.43

≤≤

0.43

 

Application and Usage

Feature X42 (L290) X52 (L360)
Common Use Gathering lines, low-pressure gas distribution, water transport. Mainline transmission, high-pressure gas/oil pipelines.
Advantage Extremely easy to weld; very cost-effective for low-stress environments. High strength-to-weight ratio; reduces material volume for long distances.
Cost Generally lower. Slightly higher due to alloying and processing.

 

PSL1 vs. PSL2 (Mandatory for both Grades)

Requirement PSL1 (Standard) PSL2 (Higher Level)
Chemical Content General limits Strict limits + Carbon Equivalent (CE)
Impact Toughness Not required Mandatory (Charpy V-Notch test)
Welding Standard procedures Strict control over Weld repairs (none on pipe body)
NDT (Inspection) Required for weld seams Mandatory for whole pipe body and ends
Traceability Basic Full Traceability (heat number to pipe)

 

GNEE API 5L High Yield Carbon Steel Pipes factory

API 5L pipeline factory

 

FAQ

What is API 5L X42 material?

It is a carbon steel pipe with extremely low levels of carbon. The alloy mix for API 5L X42 pipes commonly consists of manganese, phosphorous and sulfur. These elements promote mechanical strength in the pipe.

 

What is the yield strength of API X42?

API 5L X42 Min Yield Strength is 42100 Psi, 290 Mpa (As we called L290), Tensile Strength is the same with API 5L B 60200 Psi, 415 Mpa , Min Elongation: 21%.

 

What is the yield strength of X52?

API 5L grade X52 (L360 pipe) the yield strength minimum at 52220 Psi 360 Mpa, it's the meaning that we call this grade in the API 5L X52 or L360. Tensile strength is 66700 Psi and 460 Mpa. X52 performance is better than Grade X46, X42, and Grade B. It is a second big requirements in oil and gas pipe systems.

 

What is the chemical composition of API 5L X42?

API 5L is a specification of pipes that are used in transportations of corrosive and non-corrosive fluids and gases at high pressures. The API 5L X42 Pipe is made with a chemical composition of carbon, manganese, potassium phosphorous, molybdenum, chromium, silicon, and sulfur.