ASTM A333 Low Temperature Steel Pipe
Dec 04, 2025
ASTM A333 Low Temperature Pipe description
ASTM A333 standard specifies manufacturing requirements for seamless steel pipes used in low-temperature service, including chemical composition, mechanical properties, and heat treatment processes. Pipes conforming to this standard are typically employed in environments ranging from -45°C to -196°C, ensuring resistance to brittle fracture under cryogenic conditions.
Characteristics and Advantages of A333:
Low-Temperature Performance:
Maintains good toughness within -45°C to -100°C.
Weldability:
Easily machined and welded, suitable for complex pipeline installations.
Cost Efficiency:
Offers significant cost advantages over stainless steel while meeting cryogenic requirements.
ASTM A333 Steel Pipe Chemical Composition:
| Standard | Grade | Chemical Composition (%) | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| C | Si | Mn | P | S | Cr | Ni | Cu | Mo | V | Al | ||
| ASTM A333 | Grade 1 | ≤0.30 | 0.40~1.06 | ≤0.025 | ≤0.025 | |||||||
| Grade 3 | ≤0.19 | 0.18~0.37 | 0.31~0.64 | ≤0.025 | ≤0.025 | 3.18~3.82 | ||||||
| Grade 4 | ≤0.12 | 0.18~0.37 | 0.50~1.05 | ≤0.025 | ≤0.025 | 0.44~1.01 | 0.47~0.98 | 0.40~0.75 | 0.04~0.30 | |||
| Grade 6 | ≤0.30 | ≥0.10 | 0.29~1.06 | ≤0.025 | ≤0.025 | |||||||
| Grade 7 | ≤0.19 | 0.13~0.32 | ≤0.90 | ≤0.025 | ≤0.025 | 2.03~2.57 | ||||||
| Grade 8 | ≤0.13 | 0.13~0.32 | ≤0.90 | ≤0.025 | ≤0.025 | 8.40~9.60 | ||||||
| Grade 9 | ≤0.20 | 0.40~1.06 | ≤0.025 | ≤0.025 | 1.60~2.24 | 0.75~1.25 | ||||||
| Grade 10 | ≤0.20 | 0.10~0.35 | 1.15~1.50 | ≤0.03 | ≤0.015 | ≤0.15 | ≤0.25 | ≤0.015 | ≤0.50 | ≤0.12 | ≤0.06 | |
| Grade 11 | ≤0.10 | ≤0.35 | ≤0.6 | ≤0.025 | ≤0.025 | ≤0.50 | 35.0~37.0 | ≤0.50 | ||||
ASTM A333 Steel Pipe Mechanical Property:
| Standard | Grade | Tensile Strength (MPa) | Yield Point (MPa) | Elongation (%) | |
|---|---|---|---|---|---|
| Y | X | ||||
| ASTM A333 | Grade 1 | ≥380 | ≥205 | ≥35 | ≥25 |
| Grade 3 | ≥450 | ≥240 | ≥30 | ≥20 | |
| Grade 4 | ≥415 | ≥240 | ≥30 | ≥16.5 | |
| Grade 6 | ≥415 | ≥240 | ≥30 | ≥16.5 | |
| Grade 7 | ≥450 | ≥240 | ≥30 | ≥22 | |
| Grade 8 | ≥690 | ≥515 | ≥22 | ||
| Grade 9 | ≥435 | ≥315 | ≥28 | ||
| Grade 10 | ≥550 | ≥450 | ≥22 | ||
| Grade 11 | ≥450 | ≥240 | ≥18 | ||
ASTM A333 Steel Pipe Strike temperature condition:
| Grade | The lowest temperature for strike test | |
|---|---|---|
| °F | °C | |
| ASTM A333 Grade 1 | -50 | -45 |
| ASTM A333 Grade 3 | -150 | -100 |
| ASTM A333 Grade 4 | -150 | -100 |
| ASTM A333 Grade 6 | -50 | -45 |
| ASTM A333 Grade 7 | -100 | -75 |
| ASTM A333 Grade 8 | -320 | -195 |
| ASTM A333 Grade 9 | -100 | -75 |
| ASTM A333 Grade 10 | -75 | -60 |
ASTM A333 vs ASTM A334 Comparison Table
| Parameter | ASTM A333 | ASTM A334 |
|---|---|---|
| Standard Scope | Cryogenic Piping Systems (Straight/Bent Pipes) | Tubes for Cryogenic Exchangers & Condensers |
| Product Form | Seamless/Welded Straight Pipe (Field-bendable) | Seamless Tubes Only (As-supplied) |
| Primary Application | Cryogenic Fluid Transfer (LNG/LN₂) | Heat Exchanger Bundles, Condenser Coils |
| Temperature Range | -196°C ~ +50°C (Gr.8: -196°C) | -196°C ~ +50°C (Same grades as A333) |
| Grade Alignment | Gr.1, Gr.3, Gr.6, Gr.8 | Inherits A333 Grades (e.g., Gr.8) |
| Key Mechanical Req. | Impact Toughness Focus (Charpy V-notch) | Additional Bend/Flare Tests (Ensuring formability) |
| Special Tests | Drop Weight Tear Test (DWTT) | Flattening Test + Flaring Test (Ductility verification) |
| Size Range | OD: 8–1240 mm, WT: 1–200 mm | Smaller/Thinner: OD: 6–101 mm, WT: 0.8–12 mm |
| Surface Finish | Standard Industrial | High Smoothness (Ra≤1.6 μm) |
| Typical Applications | • LNG Terminal Transfer Lines • Liquid Ammonia Pipes |
• Air Separation Unit Condensers • LNG Vaporizer Tubes |
| Governing Codes | ASME B31.3 Pressure Piping | TEMA/HEI Exchanger Standards |
Test and inspection

Packaging and shipping








