Welded Rectangular 304 Stainless Steel Tube: Grade, Sizes and Inspection

Jun 30, 2023

Product Overview

Welded rectangular 304 stainless steel tube (grade UNS S30400, EN 1.4301) is produced by forming cold-rolled stainless strip into a square or rectangular hollow section and closing the longitudinal seam with electric resistance welding (ERW) or electric fusion welding (EFW). The austenitic matrix of roughly 18 % chromium and 8 % nickel resists atmospheric corrosion, fresh water, food-contact media and many mildly oxidising chemicals, and stays ductile from cryogenic temperatures up to about 800 °C in oxidising service. A rectangular section concentrates bending stiffness along its long axis, so frames, columns, handrails, machine bases and cleanroom structures use it where stiffness matters more than uniform hoop strength.

Grade 304 Chemistry and Mechanical Properties

Grade 304 is specified by chemistry range and by tensile properties rather than by a single fixed analysis, so the values below are the customary limits found in the welded-tube product standards.

Property Typical requirement Where it is stated
Carbon, max. 0.08 % Chemical composition
Silicon, max. 0.75 % Chemical composition
Manganese, max. 2.00 % Chemical composition
Phosphorus, max. 0.045 % Chemical composition
Sulfur, max. 0.030 % Chemical composition
Chromium 18.0 - 20.0 % Chemical composition
Nickel 8.0 - 10.5 % Chemical composition
Nitrogen, max. 0.10 % Chemical composition
Tensile strength, min. 515 MPa Tension test
0.2 % proof stress, min. 205 MPa Tension test
Elongation in 50 mm, min. 40 % Tension test
Hardness, max. 90 HRB Hardness test

The product standard chosen decides how the tube may be used. ASTM A554 covers welded stainless steel mechanical tubing for structural and decorative duty and carries no pressure rating. ASTM A312 covers welded austenitic stainless pipe for corrosive and elevated-temperature service, and ASTM A269 covers general-purpose welded tubing for instrumentation and fluid lines. EN 10217-7 covers welded stainless steel tubes for pressure purposes. Cut lengths, mill lengths and polished finishes are ordered separately, and a 3.1 inspection certificate issued against the heat number is the usual documentary evidence of grade.

Welding Route and Seam Quality

ERW / HFW - strip is roll-formed and the abutting edges are heated by high-frequency current to forging temperature and squeezed closed without filler metal; fast and economical for thin and medium walls.

EFW - the seam is welded with filler metal, which suits heavier walls and gives a well-defined weld bead that can be dressed flush.

DSAW - double submerged arc welding on both sides of the seam, used for larger rectangular sections and heavy wall thicknesses.

Seam quality is the controlling variable. The weld bead is normally scarfed and the seam is annealed in line so that chromium depletion near the fusion line does not become a preferential corrosion path. In-line eddy-current inspection detects seam defects continuously, and ultrasonic testing or a hydrostatic leak test is added when the order calls for it.

Standard Sizes, Tolerances and Mass

Section mass is calculated from the cross-sectional area, using a density of 7930 kg/m³ for grade 304: mass per metre = 2 x t x (A + B - 2t) x 10⁻⁶ x 7930, which reduces to 0.0159 x t x (A + B - 2t) for 304 and 0.0157 x t x (A + B - 2t) for carbon steel. Corner radii and any seam bead are ignored, so the calculated figure is a design value.

Size A x B (mm) Wall t (mm) Section area (mm²) Mass 304 (kg/m) Mass per 6 m (kg)
25 x 13 1.2 85.4 0.68 4.1
40 x 20 1.5 171 1.36 8.1
50 x 25 2.0 284 2.25 13.5
100 x 50 3.0 864 6.85 41.1
150 x 100 4.0 1936 15.35 92.1
200 x 100 6.0 3456 27.40 164.5

Wall thickness tolerance, corner radius, squareness and twist follow the ordering standard; the common ranges are 20 x 10 mm up to 400 x 200 mm outside dimensions, with wall from 0.8 mm to 12 mm and mill lengths of 6 m or 12 m or cut-to-length. Fixed-length cutting with a square end within 1 mm is normal for automatic welding lines.

Inspection, Ends, Finish and Packaging

Inspection - dimensional and visual check, flattening or flare test, eddy-current or ultrasonic seam inspection, and a hydrostatic or pneumatic leak test when specified.

Ends - plain cut, beveled, or threaded with coupling and cap.

Finish - bare, black painted or varnish coated, galvanized, oiled, or coated with three-layer polyethylene, fusion-bonded epoxy or another corrosion-resistant system.

Packaging - large sections in bulk, small sections in steel-strap bundles, with woven cloth, plastic bags and end caps as required.

Frequently Asked Questions

Q: Is welded rectangular 304 tube weaker than seamless tube?
No. For rectangular hollow sections there is no seamless equivalent in normal commercial supply. The weld quality, wall thickness and inspection scope determine fitness for service, and an annealed ERW seam tested by eddy current performs the same as the parent strip for structural and general corrosion duty.

Q: Can 304 rectangular tube be welded on site?
Yes. TIG welding with 308L filler is usual for thin walls, and MIG welding with 308LSi filler is used for heavier sections. Because the material is austenitic, heat tint and chromium-depleted oxide should be removed after welding to keep the corrosion resistance of the heat-affected zone.

Q: Which wall thickness should be specified for structural frames?
Wall thickness follows from the calculated bending moment and deflection limit rather than from a house rule. In practice 1.5 mm to 3.0 mm covers most light frames, and 4.0 mm to 6.0 mm is used for load-bearing bases and heavy machine guards.

Q: How does 304 behave in coastal or chloride-bearing environments?
Grade 304 resists rural and most urban atmospheres but can pit where chlorides concentrate, such as splash zones or sheltered crevices. Grade 316L, with molybdenum, is the normal choice for seawater exposure, road-salt contact and chloride process streams.

Q: What surface finishes are available?
As-welded and pickled, brushed, satin and mirror-polished finishes are all produced on welded rectangular tube. Polished tube is requested for architectural and food-equipment duty where cleanability matters.

Q: How is rectangular tube measured for weight settlement?
Mass is taken from the calculated section area or from actual weighing, with the basis stated on the order. Because corner radii and the scarf bead are ignored in the calculation, a tolerance band rather than an exact figure is normally agreed.